Welcome to plastics.com

« "The Invisible Killer" | Main

March 29, 2009

PVC Processing Problems---Plateout


                                     Conical twin screws                                           

Plateout                              

One perplexing problem that occasionally arises during long extrusion and calendering runs, especially with opaque, pigmented or filled compounds, is plateout - a term used to describe the buildup or deposit of incompatible material on the screw, in the die, on embossing rolls,roll take-up equipment or sizing sleeves.  In time this deposit affects the surface finish of the product, and also provides sites for sticking - leading to degradation.  Production down-time for clean-up is then necessary. All the factors responsible for causing plate-out are not fully understood.  It is believed that minor incompatibilities of additives are partly responsible but not the whole cause.  Changes in type and use levels of lubricants, fillers, pigments and stabilizers, as well as changes in processing conditions (speed, temperature) can affect the severity of plateout - for better or worse. Even the weather (high humidity) has been known to aggravate plateout!  Although plateout may occur in a clear formulation, most plateout incidents seem to happen with opaque, pigmented or filled compounds. Invariably, a combination of two classes of metals are usually present in plateout - prone compounds - alkaline earths (calcium, magnesium from the filler or barium from the stabilizer) and heavy metals (most commonly titanium from  titanium dioxide pigment, also lead and cadmium from stabilizers or pigments).                                

                                                                        

Several empirical approaches to the control of plateout have evolved over the years, which have shown varying degrees of effectiveness:

           1.  Stabilizers based on organotin derivatives have not been shown to contribute to plateout, mainly due to their very high compatibility or solubility in the PVC melt.  On the other hand, salts of barium, cadmium, calcium, zinc and lead are either insoluble or less compatible with the PVC melt and can aggravate plateout if other conditions are right.

           2.  Compounds based on emulsion polymerized PVC resins (E-PVC) normally cannot be induced to show plateout.  In some cases, replacing a small amount (10-20%) of suspension (S-PVC) resin with E-PVC will reduce plate-out.  This may be due to the presence of trace amounts of emulsifier present on the resin, for the addition of either cationic or anionic surfactants in very small amounts (0.1 phr) has also been shown to reduce plateout.

           3.  A mechanical approach to plateout control which has worked successfully involves the use of a small amount (0.5 phr) of a silicate filler to contribute mild abrasive or scrubbing action on metal surfaces.

           4.  A small container of mineral spirits mounted above the sizing sleeve of a vacuum cooling tank so as to permit a slow, dropwise addition of mineral spirits on the hot vinyl profile just before entering the vacuum sizer will often  keep sizing sleeves clean.

 

Lab Test for Plateout---

 

 

Skip's PVC Charts 026 

The test compound, containing DuPont's Wachtung Red pigment(notorious for showing plaeout) is processed on a two roll mill, and the sheet discarded, leaving any plateout deposit on the rolls. A high TiO2 containing white "scrubbing" compound with abrasive silicate filler is then processed on the same two roll mill, removed, and the degree of "pink" indicates the degree of plateout in the test compound. The picture shows how PVC resins and stabilizers can affect plateout.

Comments

It was a awe-inspiring post and it has a significant meaning and thanks for sharing the information.Would love to read your next post too......

Thanks

Regards

Pet preform suppliers


Incredibly inspiring article, Thank you !?!

One more new write-up with powerful points, I've been a lurker below for any brief time but wish to become a great deal much more engaged inside long term.

Hi, exactly where did you get this info can you please support this with some proof or you might say some very good reference as I and others will actually enjoy. This details is actually great and I will say will usually be helpful if we attempt it possibility free. So if you can back it up. That may really support us all. And this may well bring some good repute for you.

Thank you very much.I like this site.

No matter how you feel, you have to get up, dress up himself and then start to a new day.

Learn to use the understanding, appreciate the eyes to see each other, in order to opinionated care of each other.

I sit at my window this morning where the world like a passer-by stops for a moment, nods to me.

Let a person is strange, and the fault of others than up, our own fault often not that concerned.

Though the goodness of life are sometimes overshadowed, it can never be ignored.

Help yourself lucky man may not allows you to have a different understanding of life.

A small container of mineral spirits mounted above the sizing sleeve of a vacuum cooling tank so as to permit a slow, dropwise addition of mineral spirits on the hot vinyl profile just before entering the vacuum sizer will often keep sizing sleeves clean.

The comments to this entry are closed.

 




Partnerships :: click for details

    Discussion Forums Index
    Click to see ALL the forums